Unity Controller

A: AC INPUT - Primary power input for power supply.

B: AC INPUT - Power input here is switched by relay to the (C) ROUTER output.

C: ROUTER - Connect to the 110VAC 3-prong power cable from the machine harness. On-screen spindle controls, as well as M3/M5 g-codes will control this output. When a VFD spindle is used instead of a router, this outlet can be used with for a shop vac and is controlled by M8/M9.

D: USB - Connect to USB connector on PC. Powers the logic supply of the board.

E: PARALLEL PORT - Connect to the primary (built onto the motherboard) DB-25 connector on the PC.

F, G, H, I: MOTOR CONNECTIONS - Connect to each of the labeled motor connections from the machine harness.

J: A-AXIS - For optional rotary axis.

K: VFD - Connect to 3pin VFD pigtail for speed control of a VFD spindle.

L: LIMITS - Connect to the 8-pin limit switch connector from the machine harness.

M: E-STOP - Connect to the 2-pin e-stop connector from the machine harness.

N: EARTH GND - It is recommended that the machine is grounded to earth. Connect the two black wires from the machine harness to this connection. If using a VFD, ground the machine frame to the VFD earth ground terminal instead. Additional earth grounding may be necessary when working with certain spindles or certain types of materials that may cause excess EMI or static electricity.

O: AUX -/+ - This is a 5V logic level signal that can be connected to a PowerSwitch Tail or other 5V@20mA relay circuit. This signal is controlled by the flood coolant controls in the software (M8/M9).

	1) A Dir	10) X Limit
	2) X Step	11) Y1 Limit
	3) X Dir	12) Y2 Limit
	4) Y1 Step	13) Z Dir
	5) Y1 Dir	14) Spindle
	6) Z Step	15) E-stop
	7) Z Dir	16) Coolant
	8) Y2 Step	17) A Step
	9) Y2 Dir	18-25) GND

	1) Pin 15
	2) GND

	1) 24V In from VFD
	2) GND
	3) 0-10V

	1) B-
	2) B+
	3) NC
	4) A+
	5) A-

	1) X Limit (Pin 10)
	2) GND
	3) Y1 Limit (Pin 11)
	4) GND
	5) Z Limit (Pin 12)
	6) GND
	7) Y2 Limit (Pin 13)
	8) GND

UNITY CNC CONTROLLER Save time and money by having your stepper motor driver kit professionally wired and installed with the new Unity Controller - the only CNC control system you will ever need!

Expandable to your needs, versatile, and flexible. Can be used for 2, 3, 4, or 5 axis systems. Get it with or without motors Motors are pre-wired with 6 Feet of 5-Conductor 22Gauge Motor Wire and XLR connectors Driver System:

The Unity CNC Controller includes 5 4.2amp MondoStep Bipolar Drivers, giving you versatility. Have a machine with two motors driving the gantry? No problem. You will still have a spare back-up driver for high-reliability, or use the spare for a rotary axis, and still be able to swap it over as a backup in case you have a driver failure in a high-reliability production environment.

Breakout Board

Also is the worlds first ever, breakout board that can be configured for parallel or USB control. The PBX-MX can be used as an isolated parallel port breakout board for use with software such as LinuxCNC or Mach3. Includes an on-board Arduino compatible microcontroller that can be used for monitoring and diagnostics. By changing a couple of solder jumpers, you can program the board to become a GRBL compatible USB controller for the GRBL G-code interpreter.

Integrated back panel includes:

Connections for up to 5 motors Connector for limit switches Connector for E-Stop. Earth ground connection for improved EMI protection Auxilary 5v logic output that can drive an accessory like the powerswitch Tail II or other speed controller like the C6 spindle speed control board or SuperPID. IEC power connections for the primary power and the router control relay . PBX-MX Dual Parallel/USB breakout board Two AC inputs Color coded

Have a look inside: 40Volt (110VAC Input) Linear Power Supply for the fastest motor operation

Professionally wired, installed, mounted and tested electronics

5 Drivers, Breakout Board, IDC cables, and wired connector ports

Full Enclosure with Power switch, fan, and fuses.

Modular and organized

Unity Controller

From PROBOTIX :: wiki