Difference between revisions of "Unity-M2"
From PROBOTIX :: wiki
m |
|||
| Line 1: | Line 1: | ||
[[Category:Controllers]] | [[Category:Controllers]] | ||
[[Category:Need Pictures]] | [[Category:Need Pictures]] | ||
| − | + | ||
| + | [[File:Unity-M2_rear.png|thumb|500px|Unity-M2 Controller]] | ||
| + | |||
| + | [[Unity Controller]] customized for use with bench-top mill conversions using a higher amp Z driver with NEMA34 motor options and the replacement of the fifth driver by two extra relays. | ||
| + | * Expandable to your needs, versatile, and flexible. | ||
| + | * Can be used for 2, 3, or 4 axis systems. | ||
| + | * Get it with or without motors | ||
| + | * Motors (if purchased) are pre-wired with 6 Feet of 5-Conductor 22 Gauge Motor Wire and XLR connectors | ||
| + | |||
| + | == Have A Look Inside: == | ||
| + | * 40Volt (110VAC Input) Linear Power Supply for the fastest motor operation | ||
| + | * Professionally wired, installed, mounted and tested electronics | ||
| + | * 4 Drivers, Breakout Board, IDC cables, and wired connector ports | ||
| + | * Full Enclosure with Power switch, fan, and fuses | ||
| + | * Modular and organized | ||
| + | |||
| + | == Driver System: == | ||
| + | * 3x 5.6Amp MondoStep Bipolar Drivers (X, Y, and A axis) | ||
| + | * 1x 7.8Amp MondoStep BiPolar Driver (Z axis) | ||
| + | |||
| + | == Breakout Board: == | ||
| + | The [[PBX-MX]] is an isolated parallel port breakout board for use with software such as LinuxCNC or Mach3. | ||
| + | |||
| + | == Integrated back panel includes: == | ||
| + | * Connections for up to 4 motors | ||
| + | * Connector for limit switches | ||
| + | * Connector for E-Stop | ||
| + | * Earth ground connection for improved EMI protection | ||
| + | * Auxilary 5v logic output that can drive an accessory like the Powerswitch Tail | ||
| + | * IEC power connections for the primary power and the router control relay | ||
| + | * Built in PWM to 0-10VDC analog signal interface for spindle speed control to a VFD or SuperPID. | ||
| + | * PBX-MX Isolated Parallel Port breakout board | ||
| + | * Two AC inputs | ||
| + | * Color coded | ||
== Pin-out == | == Pin-out == | ||
| − | We recommend using LinuxCNC's coolant mist and flood for controlling Relays 1 & 2. This would provide M7 and M8 commands and on-screen checkboxes for control. | + | We recommend using LinuxCNC's coolant mist and flood for controlling Relays 1 & 2. This would provide M7 and M8 commands and on-screen checkboxes for control. |
| + | {{WarningBox|'''Note:''' These relays do not provide power, they simply open/close circuits.}} | ||
* See here for more info: [http://linuxcnc.org/docs/html/gcode/m-code.html#mcode:m7-m8-m9 M7/M8/M9] | * See here for more info: [http://linuxcnc.org/docs/html/gcode/m-code.html#mcode:m7-m8-m9 M7/M8/M9] | ||
{{ParallelPort | {{ParallelPort | ||
| Line 25: | Line 59: | ||
|17=5VDC Relay 2 | |17=5VDC Relay 2 | ||
}} | }} | ||
| + | |||
| + | {{XLR-EStop | ||
| + | |1=Pin 15 | ||
| + | |2=GND | ||
| + | }} | ||
| + | |||
| + | {{XLR-Limits | ||
| + | |1=X Limit (Pin 10) | ||
| + | |2=GND | ||
| + | |3=Y Limit (Pin 11) | ||
| + | |4=GND | ||
| + | |5=NC (Pin 12) | ||
| + | |6=GND | ||
| + | |7=Z Limit (Pin 13) | ||
| + | |8=GND | ||
| + | }} | ||
| + | |||
| + | {{XLR-VFD | ||
| + | |1=24V in from VFD | ||
| + | |2=GND | ||
| + | |3=0-10V | ||
| + | }} | ||
| + | |||
| + | {{XLR-Motors | ||
| + | |1=B- | ||
| + | |2=B+ | ||
| + | |3=NC | ||
| + | |4=A+ | ||
| + | |5=A- | ||
| + | }} | ||
| + | |||
| + | == Example Config == | ||
| + | Example LinuxCNC config: [[File: Unity-M2.zip]] | ||
Revision as of 17:15, 27 November 2018
Unity Controller customized for use with bench-top mill conversions using a higher amp Z driver with NEMA34 motor options and the replacement of the fifth driver by two extra relays.
- Expandable to your needs, versatile, and flexible.
- Can be used for 2, 3, or 4 axis systems.
- Get it with or without motors
- Motors (if purchased) are pre-wired with 6 Feet of 5-Conductor 22 Gauge Motor Wire and XLR connectors
Contents
Have A Look Inside:
- 40Volt (110VAC Input) Linear Power Supply for the fastest motor operation
- Professionally wired, installed, mounted and tested electronics
- 4 Drivers, Breakout Board, IDC cables, and wired connector ports
- Full Enclosure with Power switch, fan, and fuses
- Modular and organized
Driver System:
- 3x 5.6Amp MondoStep Bipolar Drivers (X, Y, and A axis)
- 1x 7.8Amp MondoStep BiPolar Driver (Z axis)
Breakout Board:
The PBX-MX is an isolated parallel port breakout board for use with software such as LinuxCNC or Mach3.
Integrated back panel includes:
- Connections for up to 4 motors
- Connector for limit switches
- Connector for E-Stop
- Earth ground connection for improved EMI protection
- Auxilary 5v logic output that can drive an accessory like the Powerswitch Tail
- IEC power connections for the primary power and the router control relay
- Built in PWM to 0-10VDC analog signal interface for spindle speed control to a VFD or SuperPID.
- PBX-MX Isolated Parallel Port breakout board
- Two AC inputs
- Color coded
Pin-out
We recommend using LinuxCNC's coolant mist and flood for controlling Relays 1 & 2. This would provide M7 and M8 commands and on-screen checkboxes for control.
Note: These relays do not provide power, they simply open/close circuits.
- See here for more info: M7/M8/M9
|
1) 5VDC Relay 1 | 10) X Limit |
| 2) X Step | 11) Y1 Limit | |
| 3) X Dir | 12) Y2 Limit | |
| 4) Y1 Step | 13) Z Limit | |
| 5) Y1 Dir | 14) 120VAC Relay | |
| 6) Z Step | 15) E-stop | |
| 7) Z Dir | 16) 5VDC AUX | |
| 8) Y2 Step | 17) 5VDC Relay 2 | |
| 9) Y2 Dir | 18-25) GND |
|
1) Pin 15 |
| 2) GND |
|
1) X Limit (Pin 10) |
| 2) GND | |
| 3) Y Limit (Pin 11) | |
| 4) GND | |
| 5) NC (Pin 12) | |
| 6) GND | |
| 7) Z Limit (Pin 13) | |
| 8) GND |
|
1) 24V in from VFD |
| 2) GND | |
| 3) 0-10V |
|
1) B- |
| 2) B+ | |
| 3) NC | |
| 4) A+ | |
| 5) A- |
Example Config
Example LinuxCNC config: File:Unity-M2.zip