Difference between revisions of "Touch Probe"
From PROBOTIX :: wiki
| Line 4: | Line 4: | ||
http://meshlab.sourceforge.net/ | http://meshlab.sourceforge.net/ | ||
| + | |||
| + | http://wiki.linuxcnc.org/cgi-bin/wiki.pl?Touch_Probe | ||
| + | |||
| + | http://www.timeguy.com/cradek/01262579508 | ||
| + | |||
| + | http://lab.whitequark.org/notes/2014-07-06/g38-probing-workpieces-in-linuxcnc/ | ||
| + | |||
| + | http://www.scorchworks.com/Blog/auto-probing-with-g-code-ripper/ | ||
| + | |||
| + | http://www.scorchworks.com/Gcoderipper/gcoderipper.html | ||
| + | |||
| + | LinuxCNC is distributed with gridprobe.ngc and smartprobe.ngc | ||
| + | |||
| + | <code> | ||
| + | ( Rectangular Probing ) | ||
| + | ( ) | ||
| + | ( This program repeatedly probes in a regular XY grid and writes the ) | ||
| + | ( probed location to the file 'probe-results.txt' in the same directory ) | ||
| + | ( as the .ini file ) | ||
| + | |||
| + | (Configuration section) | ||
| + | G20 (Inches) | ||
| + | F4 (probe speed) | ||
| + | |||
| + | #1=0 (X start) | ||
| + | #2=.25 (X increment) | ||
| + | #3=13 (X count) | ||
| + | |||
| + | #4=0 | ||
| + | #5=.25 | ||
| + | #6=5 (Y count) | ||
| + | |||
| + | #7=.1 (Z safety) | ||
| + | #8=-.5 (Z probe) | ||
| + | (End configuration section) | ||
| + | |||
| + | (PROBEOPEN probe-results.txt) | ||
| + | #9=0 #10=0 | ||
| + | G0Z#7 | ||
| + | O1 while [#9 lt #6] | ||
| + | #10=0 | ||
| + | G0 Y[#4+#5*#9] | ||
| + | O2 while [#10 lt #3] | ||
| + | O3 if [[#9/2] - fix[#9/2] eq 0] | ||
| + | G0X[#1+#2*#10] | ||
| + | O3 else | ||
| + | G0X[#1+#2*[#3-#10-1]] | ||
| + | O3 endif | ||
| + | G38.2Z#8 | ||
| + | G0Z#7 | ||
| + | #10=[#10+1] | ||
| + | O2 endwhile | ||
| + | #9=[#9+1] | ||
| + | O1 endwhile | ||
| + | |||
| + | (PROBECLOSE) | ||
| + | G0Z#7 | ||
| + | G0X#1Y#4 | ||
| + | M2 | ||
| + | </code> | ||
Revision as of 06:18, 4 September 2015
http://www.craftycnc.com/touch-probes/
http://www.ebay.com/itm/171912530881
http://meshlab.sourceforge.net/
http://wiki.linuxcnc.org/cgi-bin/wiki.pl?Touch_Probe
http://www.timeguy.com/cradek/01262579508
http://lab.whitequark.org/notes/2014-07-06/g38-probing-workpieces-in-linuxcnc/
http://www.scorchworks.com/Blog/auto-probing-with-g-code-ripper/
http://www.scorchworks.com/Gcoderipper/gcoderipper.html
LinuxCNC is distributed with gridprobe.ngc and smartprobe.ngc
( Rectangular Probing )
( )
( This program repeatedly probes in a regular XY grid and writes the )
( probed location to the file 'probe-results.txt' in the same directory )
( as the .ini file )
(Configuration section) G20 (Inches) F4 (probe speed)
- 1=0 (X start)
- 2=.25 (X increment)
- 3=13 (X count)
- 4=0
- 5=.25
- 6=5 (Y count)
- 7=.1 (Z safety)
- 8=-.5 (Z probe)
(End configuration section)
(PROBEOPEN probe-results.txt)
- 9=0 #10=0
G0Z#7 O1 while [#9 lt #6]
#10=0
G0 Y[#4+#5*#9]
O2 while [#10 lt #3]
O3 if [[#9/2] - fix[#9/2] eq 0]
G0X[#1+#2*#10]
O3 else
G0X[#1+#2*[#3-#10-1]]
O3 endif
G38.2Z#8
G0Z#7
#10=[#10+1]
O2 endwhile
#9=[#9+1]
O1 endwhile
(PROBECLOSE) G0Z#7 G0X#1Y#4 M2