Difference between revisions of "Galaxy Series LinuxCNC Configuration"

Revision as of 10:00, 12 April 2016

Welcome to the new Galaxy Series Universal Configurator. This script will reconfigure the LinuxCNC software to add or remove features on your machine and has additional functionality to manage the most common problems in the hopes of maximizing uptime on your machine. This script will also be used to install software updates when they are released. Follow the on screen prompts carefully, but do not worry if you make a mistake as you can simply re-run the script to correct any errors.

Important: Only run this script when you can afford to have the machine go down temporarily, as you may need to call us if anything goes wrong. We have tested this script several hundred times on as many machines as we could, but as with any software update, results can go not as you planned. If you are concerned, then CALL US TO SCHEDULE A TIME TO DO THE UPGRADE.

Follow the onscreen prompts.

Step 1: Enter your order number.

Step 2: Choose which machine you have.

Step 3: Do you use a router or one of the 80mm VFD spindles?

Step 3b: If you have a router, you need to choose which mount you have so that we can adjust for the distance to the center of the tool. Here is a diagram to help decide: [Router Mount Diagram]

Step 4: Do you want the machine to run in inches or mm?

Step 4b: If you have a custom travel machine, you need to enter the X & Y travel here.

Step 5: Do you have the older Roton (black drive nuts) or the newer Helix (blue drive nuts) ACME screws?

Step 6: Do you have the older Probostep (uni-polar) or newer MondoStep (bi-polar) drivers?

Step 7: Do you use the gamepad jog controller?

Step 8: Accept the default parallel port addressing, or enter custom addressing if instructed by us to do so.

Step 9: Do you use the ATLaS tool sensor, the Z-puck, neither or both? Here you can also move the Unity parallel cable to the second port for diagnostics if directed by us to do so.

Step 9b: If you use the Z-puck, this step will ask you for the height of your puck. Measure your puck with a set of calipers and enter the inch or mm measurement here.

Step 10: Do you use the rotary axis?

Step 11: On this step you can swap a motor to the a-axis header. You can do this if you have a driver failure to get back up and running in a hurry while waiting on replacement parts. You will lose use of the rotary when configured like this.

Step 12: If you are having intermittent limit switch issues from faulty switches or electrical noise, you can configure the machine to use soft limits only.

Axis Rev1.4 Interface

New desktop background and LinuxCNC launch splash screen

There is now a folder shortcut to the nc_files directory right on the desktop. Now you can just drag your g-code files onto this shortcut after the windows pops up showing the contents of your USB thumb drive.

The new configurator will allow you to set the interface to run natively in metric (mm) mode.

LinuxCNC will now run initializing g-code in case your post processor doesn't insert the proper setup codes.

[Home All] has been renamed to [Home Machine]

[Touch-off] has been renamed to [Set Axis Origin]

After homing, the machine used to drive to the center of the table. Now the park after homing position is at absolute machine zero (front/left/up).

The G28 Button has been replaced by the [Bring To Front] button. It is now hard coded to be the center of the back of the machine all the way up on the Z. G28 is now free to use for other purposes.

The G30 Button has been replaced by the [Park At Rear] button. It is also now hard coded, but to the center of the front of the machine all the way up on the Z. G30 is now free to be used for other purposes.

There is a new [Return To Home] button that will bring the machine back to machine zero home.

There is a new [Return to X/Y Origin] button that will drive the machine back to the X/Y origin of the part.

[Load 1st Tool] has been renamed to [Measure First Tool]. If you do not have the ATLaS tool sensor, this button will no longer appear.

There is a new [Set Z Origin] button for quickly setting the current z position to zero for the current coordinate system.

If you have the Z-Puck, there is a new button for setting the Z-axis origin using the Z-puck. Click here to learn how to use it:Z_Touch-off_Puck

There is a new [Set X/Y Origin] to quickly set both the X & Y origin to zero for the current coordinate system simultaneously.

There is a new [G-code Reset] button that runs the initializing setup codes again. Use this button if you get lost, for instance if you forget what coordinate system you are in. The setup codes are G0 G54 G17 G20 G90 G40 G49 G64 P0.010 for machines configured for inch.

Joint number on limit switch errors will now display the axis name instead of the joint number.

ATLaS tool change routine is now o100 [tool_number] for both inch and mm configs.

ATLaS tool change routine will now skip driving to the front if the tool has already been measured.

Other (less sexy) things the configurator does

Changes color of terminal window to classic linux shell.
Installs php scripting engine
Installs numlockx to force numb lock key on
Installs g-code-filter.php to clean up .ngc2 files (not sexy, yet - but its gonna be)
Tries to identify secondary parallel port address, copies lspci output to thumb drive incase you need to email it to us
Disables screensaver and idle screen lock
Uninstalls the update manager
Turns line numbers on in gedit

Revision as of 08:09, 12 April 2016 (view source) Admin (Talk \| contribs) (→‎Follow the onscreen prompts.) ← Older edit		Revision as of 10:00, 12 April 2016 (view source) Admin (Talk \| contribs) (→‎Axis Rev1.4 Interface) Newer edit →
Line 100:		Line 100:

	:*ATLaS tool change routine is now o100 [tool_number] for both inch and mm configs.		:*ATLaS tool change routine is now o100 [tool_number] for both inch and mm configs.
		+
		+	:*ATLaS tool change routine will now skip driving to the front if the tool has already been measured.