Difference between revisions of "PBX-USB"
From PROBOTIX :: wiki
| Line 1: | Line 1: | ||
[[category:Breakout Boards]] | [[category:Breakout Boards]] | ||
[[image:PBX-USB.jpg|thumb|500px|PBX-USB]] | [[image:PBX-USB.jpg|thumb|500px|PBX-USB]] | ||
| − | The PBX-USB is a USB interfaced CNC controller that was developed specifically to work with the CNC USB Motion Controller Software from www.planet-cnc.com. This Interface sports 4x 10 pin PBX-Header Connections for interfacing to our existing stepper motor drivers. It has an additional header for direct connection to our RBX-1 3 channel relay board. This software/hardware combination can be further expanded with jog key inputs and an I2C bus for nearly unlimited additional I/O. This will allow the development of jog pendants, digital readouts, and input/output cards for a variety of purposes. The software runs on Windows and replaces Mach3 or EMC2. It can even be run through a virtual machine on a Mac or Linux host. | + | |
| + | == Hardware Features: == | ||
| + | :*4 axis USB CNC controller | ||
| + | :*USB (V2.x) from PC/Laptop running Windows XP, Vista or Windows 7(32 bit or 64 bit) | ||
| + | :*3 digital outputs (flood, mist, spindle) | ||
| + | :*25 KHz maximum step frequency | ||
| + | :*12us minimum pulse width | ||
| + | :*Buffered I/O for maximum performance | ||
| + | :*Two manual jog input keys per axis (8 total) | ||
| + | :*Two limit switches for X,Y, Z (6 total) | ||
| + | :*Jog Pendant Interface ?Relay Board Interface | ||
| + | :*I2C Interface | ||
| + | :*E-Stop Loop | ||
| + | |||
| + | == Software Features: == | ||
| + | :*Advanced interpolation algorithms | ||
| + | :*Control external devices with I2C protocol | ||
| + | :*Pause/resume of execution supported | ||
| + | :*Automatic homing procedure | ||
| + | :*Touch Plate Tool Change Procedure | ||
| + | :*Standard RS274/NGC G-code (EMC2 compatible) | ||
| + | :*Toolpath simulation | ||
| + | :*Advanced G-codes - G40, G41, G42 (Cutter Radius Compensation) | ||
| + | :*supported ?Advanced G-codes - G43, G49 (Tool Length Offsets) supported | ||
| + | :*Advanced G-codes - G54, G59.3 (Coordinate System Origins) | ||
| + | |||
| + | |||
| + | == Description == | ||
| + | |||
| + | The PBX-USB is a USB interfaced CNC controller that was developed specifically to work with the CNC USB Motion Controller Software from [[link:www.planet-cnc.com]]. This Interface sports 4x 10 pin PBX-Header Connections for interfacing to our existing stepper motor drivers. It has an additional header for direct connection to our RBX-1 3 channel relay board. This software/hardware combination can be further expanded with jog key inputs and an I2C bus for nearly unlimited additional I/O. This will allow the development of jog pendants, digital readouts, and input/output cards for a variety of purposes. The software runs on Windows and replaces Mach3 or EMC2. It can even be run through a virtual machine on a Mac or Linux host. | ||
www.planet-cnc.com | www.planet-cnc.com | ||
Revision as of 09:53, 20 September 2013
Hardware Features:
- 4 axis USB CNC controller
- USB (V2.x) from PC/Laptop running Windows XP, Vista or Windows 7(32 bit or 64 bit)
- 3 digital outputs (flood, mist, spindle)
- 25 KHz maximum step frequency
- 12us minimum pulse width
- Buffered I/O for maximum performance
- Two manual jog input keys per axis (8 total)
- Two limit switches for X,Y, Z (6 total)
- Jog Pendant Interface ?Relay Board Interface
- I2C Interface
- E-Stop Loop
Software Features:
- Advanced interpolation algorithms
- Control external devices with I2C protocol
- Pause/resume of execution supported
- Automatic homing procedure
- Touch Plate Tool Change Procedure
- Standard RS274/NGC G-code (EMC2 compatible)
- Toolpath simulation
- Advanced G-codes - G40, G41, G42 (Cutter Radius Compensation)
- supported ?Advanced G-codes - G43, G49 (Tool Length Offsets) supported
- Advanced G-codes - G54, G59.3 (Coordinate System Origins)
Description
The PBX-USB is a USB interfaced CNC controller that was developed specifically to work with the CNC USB Motion Controller Software from link:www.planet-cnc.com. This Interface sports 4x 10 pin PBX-Header Connections for interfacing to our existing stepper motor drivers. It has an additional header for direct connection to our RBX-1 3 channel relay board. This software/hardware combination can be further expanded with jog key inputs and an I2C bus for nearly unlimited additional I/O. This will allow the development of jog pendants, digital readouts, and input/output cards for a variety of purposes. The software runs on Windows and replaces Mach3 or EMC2. It can even be run through a virtual machine on a Mac or Linux host.
www.planet-cnc.com
Diagram:
- Notes: