Actions

Difference between revisions of "Unity-M2"

From PROBOTIX :: wiki

m
 
(3 intermediate revisions by the same user not shown)
Line 1: Line 1:
−
[[Category:Controllers]]
+
[[Category:CNC Controllers]]
−
[[Category:Need Pictures]]
+
 
−
Example LinuxCNC config: [[File: Unity-M2.zip]]
+
[[File:Unity-M2_rear.png|thumb|500px|Unity-M2 Controller]]
 +
 
 +
[[Unity Controller]] customized for use with bench-top mill conversions using a higher amp Z driver with NEMA34 motor options and the replacement of the fifth driver by two extra relays.
 +
* Expandable to your needs, versatile, and flexible.
 +
* Can be used for 2, 3, or 4 axis systems.
 +
* Get it with or without motors
 +
* Motors (if purchased) are pre-wired with 6 Feet of 5-Conductor 22 Gauge Motor Wire and XLR connectors
 +
 
 +
== Have A Look Inside: ==
 +
* 40Volt (110VAC Input) Linear Power Supply for the fastest motor operation
 +
* Professionally wired, installed, mounted and tested electronics
 +
* 4 Drivers, Breakout Board, IDC cables, and wired connector ports
 +
* Full Enclosure with Power switch, fan, and fuses
 +
* Modular and organized
 +
 
 +
== Driver System: ==
 +
* 3x 5.6Amp MondoStep Bipolar Drivers (X, Y, and A axis)
 +
* 1x 7.8Amp MondoStep BiPolar Driver (Z axis)
 +
 
 +
== Breakout Board: ==
 +
The [[PBX-MX]] is an isolated parallel port breakout board for use with software such as LinuxCNC or Mach3.
 +
 
 +
== Integrated back panel includes: ==
 +
* Connections for up to 4 motors
 +
* Connector for limit switches
 +
* Connector for E-Stop
 +
* Earth ground connection for improved EMI protection
 +
* Auxilary 5v logic output that can drive an accessory like the Powerswitch Tail
 +
* IEC power connections for the primary power and the router control relay
 +
* Built in PWM to 0-10VDC analog signal interface for spindle speed control to a VFD or SuperPID.
 +
* PBX-MX Isolated Parallel Port breakout board
 +
* Two AC inputs
 +
* Color coded
  
 
== Pin-out ==
 
== Pin-out ==
−
We recommend using LinuxCNC's coolant mist and flood for controlling Relays 1 & 2. This would provide M7 and M8 commands and on-screen checkboxes for control.
+
We recommend using LinuxCNC's coolant mist and flood for controlling Relays 1 & 2. This would provide M7 and M8 commands and on-screen checkboxes for control.  
 +
{{WarningBox|'''Note:''' These relays do not provide power, they simply open/close circuits.}}
 
* See here for more info: [http://linuxcnc.org/docs/html/gcode/m-code.html#mcode:m7-m8-m9 M7/M8/M9]
 
* See here for more info: [http://linuxcnc.org/docs/html/gcode/m-code.html#mcode:m7-m8-m9 M7/M8/M9]
 
{{ParallelPort
 
{{ParallelPort
Line 25: Line 58:
 
|17=5VDC Relay 2
 
|17=5VDC Relay 2
 
}}
 
}}
 +
 +
{{XLR-EStop
 +
|1=Pin 15
 +
|2=GND
 +
}}
 +
 +
{{XLR-Limits
 +
|1=X Limit (Pin 10)
 +
|2=GND
 +
|3=Y Limit (Pin 11)
 +
|4=GND
 +
|5=NC (Pin 12)
 +
|6=GND
 +
|7=Z Limit (Pin 13)
 +
|8=GND
 +
}}
 +
 +
{{XLR-VFD
 +
|1=24V in from VFD
 +
|2=GND
 +
|3=0-10V
 +
}}
 +
 +
{{XLR-Motors
 +
|1=B-
 +
|2=B+
 +
|3=NC
 +
|4=A+
 +
|5=A-
 +
}}
 +
 +
{{XLR-Relays
 +
|1=Relay 1
 +
|2=NC
 +
|3=Relay 2
 +
}}
 +
 +
== Example Config ==
 +
Example LinuxCNC config: [[File: Unity-M2.zip]]

Latest revision as of 06:56, 23 August 2019

Unity-M2 Controller

Unity Controller customized for use with bench-top mill conversions using a higher amp Z driver with NEMA34 motor options and the replacement of the fifth driver by two extra relays.

  • Expandable to your needs, versatile, and flexible.
  • Can be used for 2, 3, or 4 axis systems.
  • Get it with or without motors
  • Motors (if purchased) are pre-wired with 6 Feet of 5-Conductor 22 Gauge Motor Wire and XLR connectors

Have A Look Inside:

  • 40Volt (110VAC Input) Linear Power Supply for the fastest motor operation
  • Professionally wired, installed, mounted and tested electronics
  • 4 Drivers, Breakout Board, IDC cables, and wired connector ports
  • Full Enclosure with Power switch, fan, and fuses
  • Modular and organized

Driver System:

  • 3x 5.6Amp MondoStep Bipolar Drivers (X, Y, and A axis)
  • 1x 7.8Amp MondoStep BiPolar Driver (Z axis)

Breakout Board:

The PBX-MX is an isolated parallel port breakout board for use with software such as LinuxCNC or Mach3.

Integrated back panel includes:

  • Connections for up to 4 motors
  • Connector for limit switches
  • Connector for E-Stop
  • Earth ground connection for improved EMI protection
  • Auxilary 5v logic output that can drive an accessory like the Powerswitch Tail
  • IEC power connections for the primary power and the router control relay
  • Built in PWM to 0-10VDC analog signal interface for spindle speed control to a VFD or SuperPID.
  • PBX-MX Isolated Parallel Port breakout board
  • Two AC inputs
  • Color coded

Pin-out

We recommend using LinuxCNC's coolant mist and flood for controlling Relays 1 & 2. This would provide M7 and M8 commands and on-screen checkboxes for control.

Note: These relays do not provide power, they simply open/close circuits.
Parallel Port 1) 5VDC Relay 1 10) X Limit
2) X Step 11) Y1 Limit
3) X Dir 12) Y2 Limit
4) Y1 Step 13) Z Limit
5) Y1 Dir 14) 120VAC Relay
6) Z Step 15) E-stop
7) Z Dir 16) 5VDC AUX
8) Y2 Step 17) 5VDC Relay 2
9) Y2 Dir 18-25) GND
ESTOP

2-pin E-stop Connector 		1) Pin 15
2) GND
LIMITS

8-pin Limit Switch Connector 		1) X Limit (Pin 10)
2) GND
3) Y Limit (Pin 11)
4) GND
5) NC (Pin 12)
6) GND
7) Z Limit (Pin 13)
8) GND
VFD

3-pin VFD Connector 		1) 24V in from VFD
2) GND
3) 0-10V
MOTOR

5-pin Motor Connector 		1) B-
2) B+
3) NC
4) A+
5) A-
5-pin Motor Connector 1 & 2) Relay 1
3) NC
4 & 5) Relay 2

Example Config

Example LinuxCNC config: File:Unity-M2.zip

Retrieved from "https://www.probotix.com/wiki/index.php?title=Unity-M2&oldid=14253"